Linux version 2.6.16.18 (root@ptolemy) (gcc version 3.4.5 (Gentoo 3.4.5-r1, ssp-3.4.5-1.0, pie-8.7.9)) #1 Thu May 25 08:24:51 EST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001dff0000 (usable)
 BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS)
 BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
479MB LOWMEM available.
On node 0 totalpages: 122864
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 118768 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:0
DMI 2.2 present.
ACPI: RSDP (v000 VT9174                                ) @ 0x000f6570
ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000
ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040
ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 20000000 (gap: 1e000000:e1ff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 vga=0x307
No local APIC present or hardware disabled
mapped APIC to ffffd000 (013c1000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1199.924 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 483052k/491456k available (2474k kernel code, 7880k reserved, 721k data, 184k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2403.19 BogoMIPS (lpj=4806389)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0381b93f 00000000 00000000 00000000 00000000 000000dd 00000000
CPU: Centaur VIA Nehemiah stepping 08
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 12b0)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=3
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by vt8235 PM
PCI quirk: region 0500-050f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 4 5 6 7 *12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 4 5 6 *7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 *4 5 6 7 12)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:02: ioport range 0x400-0x47f could not be reserved
pnp: 00:02: ioport range 0x500-0x50f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e8000000-e9ffffff
  PREFETCH window: e4000000-e7ffffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 20000000-21ffffff
  MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0a.1
  IO window: 00001800-000018ff
  IO window: 00001c00-00001cff
  PREFETCH window: 24000000-25ffffff
  MEM window: 26000000-27ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
vesafb: framebuffer at 0xe4000000, mapped to 0xde880000, using 2560k, total 32768k
vesafb: mode is 1280x1024x8, linelength=1280, pages=24
vesafb: protected mode interface info at c000:7e96
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
Real Time Clock Driver v1.12ac
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 5
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: WDC WD84AA, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 16514064 sectors (8455 MB) w/2048KiB Cache, CHS=16383/16/63, UDMA(66)
hda: cache flushes not supported
 hda: hda1 hda2 hda3 < hda5 >
libata version 1.20 loaded.
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0a.0 [1106:aa01]
Yenta: ISA IRQ mask 0x0c08, PCI irq 5
Socket status: 30000820
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
Yenta: CardBus bridge found at 0000:00:0a.1 [1106:aa01]
Yenta: ISA IRQ mask 0x0c08, PCI irq 12
Socket status: 30000006
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 4 (level, low) -> IRQ 4
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 4, io mem 0xea019000
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 5, io base 0x0000b000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
pccard: CardBus card inserted into slot 0
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 12, io base 0x0000b400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ 7
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 7, io base 0x0000b800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
mice: PS/2 mouse device common for all mice
padlock: Using VIA PadLock ACE for AES algorithm.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
ip_conntrack version 2.4 (3839 buckets, 30712 max) - 212 bytes per conntrack
input: AT Translated Set 2 keyboard as /class/input/input0
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
Using IPI Shortcut mode
ACPI wakeup devices: 
PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 LAN0 AC97 MC97 
ACPI: (supports S0 S1 S4 S5)
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Adding 498004k swap on /dev/hda2.  Priority:-1 extents:1 across:498004k
EXT3 FS on hda5, internal journal
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
eth0: VIA Rhine II at 0xea01a000, 00:40:63:dc:ed:35, IRQ 5.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:02:00.0 to 64
tulip0:  MII transceiver #1 config 3100 status 7869 advertising 05e1.
eth1: ADMtek Comet rev 17 at 00011000, 00:14:6C:30:BB:98, IRQ 5.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
device eth0 entered promiscuous mode
eth0: Promiscuous mode enabled.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
br0: port 1(eth0) entering learning state
0000:02:00.0: tulip_stop_rxtx() failed
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
0000:02:00.0: tulip_stop_rxtx() failed
eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
PPP BSD Compression module registered
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().

***************************** System hang for several hours
***************************** Restarted when LAN machine requested DHCP lease

***************************** Drop to single-user mode, repair time 
nfsd: last server has exited
nfsd: unexporting all filesystems
br0: port 1(eth0) entering disabled state
eth0: Promiscuous mode enabled.
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
0000:02:00.0: tulip_stop_rxtx() failed

***************************** back to multi user

eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
eth0: Promiscuous mode enabled.
br0: port 1(eth0) entering learning state
0000:02:00.0: tulip_stop_rxtx() failed
0000:02:00.0: tulip_stop_rxtx() failed
eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.