Usage: %s <port|#> <0|1|#> [options]
       <port|#>    Flash devices located at the specified base or any, '#',
                   port address.  Port address must be in hexadecimal.
       <0|1|#>     Flash master, '0', slave, '1', or both, '#', devices.
       -f <file>   Specify the filename prefix of the flash files.
                   This defaults to 'seaflash' if not provided.  Filename
                   extensions '.fls', '.ovl', '.crt', and '.tbl' are assumed.
       -c          Send a congen file, fully specified by -f.
       -r          Include the serial flash file when flashing.
       -s          Only send a single file, fully specified by -f.
       -e <rev>    Exclude firmare if this version exists.
       -v          Toggles verbose mode on/off.  Default is off.
       -l          List supported models.
       -u          Feature spin up

Usage: %s <port|#> <0|1|#> [options]
       <port|#>    Flash devices located at the specified base or any, '#',
                   port address.  Port address must be in hexadecimal.
       <0|1|#>     Flash master, '0', slave, '1', or both, '#', devices.
       -e <rev>    Exclude firmare if this version exists.
       -v          Toggles verbose mode on/off.  Default is off.
       -l          List supported models.
       -u          Feature spin up
       -k <UID>    Specify the unique descriptor to flash
       -z          Spin down after flashing (Standby Immediate)

Usage: %s -m <name> [options]
       -m <name>    Specify the model family to flash.
       -f <file>    Specify the filename prefix of the flash files.
                    This defaults to 'seaflash' if not provided.  Filename
                    extensions '.fls', '.ovl', '.crt', and '.tbl' are assumed.
       -g <file>    read a configuration file to get information on whether the 
                    firmware should be downloaded to the specified model drive,
                    please refer to 'cfgreadme.txt'.
       -h <file>    read a configuration file to check valid drive model,
                    firmware version(full name)and firmware file name line by
                    line.if match all the parameters, starts downloading.
                    please refer to 'hcfgreadme.txt'
       -j <file>    encrypt the config file for -h option from *.cfg to *.cfs.
       -o <file>    decrypt the config file for -h option from *.cfs to *.cfg.
       -c           Send a congen file, fully specified by -f.
       -r           Include the serial flash file when flashing.
       -s           Only send a single file, fully specified by -f.
       -p <port>    Only flash devices located at the specified base
                    port address.  Port address must be in hexadecimal.
       -d <0|1>     Only flash master, '0', or slave, '1', devices.
       -e <rev>     Exclude firmare if this version exists.
       -v           Toggles verbose mode on/off.  Default is off.
       -l           List supported family names and models.
       -u           Feature spin up
       -n           Disable Promise 66/100/133 card.
       -b           Segmented download of DLDxx.BIN files , or
                    the -f <file> if specified.
       -w           SMART Clear Logs.
       -t           Diagnostics Unlock Of M2TD.
       -i <Model>   Tolerent or Explicit Model Check.
       -k <UID>     Specify the unique descriptor to flash
       -a <seconds> Specify how long to delay after download complete
       -z           Spin down after flashing (Standby Immediate)

Usage: %s -<target> <datafile> -m <name> [options]
       -<target>   pm, ps, sm, ss (pm = primary master, etc..)
       -m <name>   Specify the model family to flash.
       -c          Send a congen file.
       -r          Include the serial flash file when flashing.
       -s          Only send a single file, fully specified by -f.
       -v          Toggles verbose mode on/off.  Default is off.
       -l          List supported family names and models.
       -b          Segmented download of DLDxx.BIN files or the -f <file> if specified.
       -w          SMART Clear Logs.
       -f <file>   Specify the filename prefix of the flash files.
                   This defaults to 'seaflash' if not provided.  Filename
                   extensions '.fls', '.ovl', '.crt', and '.tbl' are assumed.
       -k <UID>    Specify the unique descriptor to flash.