1095 0640 1039 0601

ModelNotFound


UM8886B PCI IDE WINDOWS 95 DEVICE DRIVERCOPYRIGHT 1995 UMC. All Rights Reserved.

IssueIdentify: Checking for IDE. Status (%x)
IssueIdentify: Resetting controller.
IssueIdentify: Checking for ATAPI. Status (%x)
IssueIdentify: DRQ never asserted (%x). Error reg (%x)
IssueIdentify: Status after soft reset (%x)
IssueIdentify: Status before read words %x
IssueIdentify: Device interrupts on assertion of DRQ.
IssueIdentify: Device does not interrupt on assertion of DRQ.
IssueIdentify: Device is a tape drive.
IssueIdentify: Device is not a tape drive.
IssueIdentify: Status after read words (%x)

SetDriveParameters: Number of heads %x
SetDriveParameters: Sectors per track %x

AtapiResetController: Reset IDE
AtapiResetController: Status before Atapi reset (%x).
AtapiResetController: Status after soft reset %x
AtapiResetController: SetDriveParameters failed
AtapiResetController: BlockModeSetup failed
AtapiResetController: IDEDiskTransferModeSetup failed

MapError: Error register is %x

ATAPI: No sense information
ATAPI: Recovered error
ATAPI: Device not ready
ATAPI: Media error
ATAPI: Hardware error
ATAPI: Illegal request
ATAPI: Unit attention
ATAPI: Data protect
ATAPI: Blank check
ATAPI: Invalid sense information
ATAPI: Media change
ATAPI: Command abort
ATAPI: End of media
ATAPI: Illegal length
ATAPI: Bad block
ATAPI: Id not found
ATAPI: Unknown error

AtapiHwInitialize: Device %x is ATAPI
AtapiHwInitialize: Device %x not responding
AtapiHwInitialize: Device %x is IDE
AtapiHwInitialize: Found nasty Compaq ESDI!
AtapiHwInitialize: Found nasty Compaq ESDI!
AtapiHwInitialize: Found nasty UltraStor ESDI!

FindDevices: Resetting controller before SetDriveParameters.
FindDevices: Status before SetDriveParameters: (%x) 

AtapHwInitialize: Set drive parameters for device %d failed

InterruptBaseAddressAtapiFindController: First access to status %x

AtapiFindController: Identifier read back from Master (%x)
AtapiFindController: Identifier read back from Slave (%x)
AtapiFindController: Found IDE at %x
dump
AtapiFindController: Crash dump
AtapiFindController: Atapi Only
AtapiFindController: Atapi Only

1060 673A

Found broken PCI IDE controller: VendorId %s, DeviceId %s

AtapiFindPciController: Identifier read back from Master (%x)
AtapiFindPciController: Identifier read back from Slave (%x)
AtapiFindPciController: Found broken IDE at %x

AtapiInterrupt: CurrentSrb is NULL
AtapiInterrupt: Entered with status (%x)
AtapiInterrupt: Unexpected interrupt.
AtapiInterrupt: Hit BUSY while polling during crashdump.
AtapiInterrupt: BUSY on entry, resetting. status %x
AtapiInterrupt: Writing Atapi packet.
AtapiInterrupt: %d words requested; %d words xferred
AtapiInterrupt: Write interrupt
AtapiInterrupt: Int reason %x, but srb is for a write %x.
AtapiInterrupt: %d words requested; %d words xferred
AtapiInterrupt: Read interrupt
AtapiInterrupt: Int reason %x, but srb is for a read %x.
AtapiInterrupt: Resetting due to BSY still up - %x
AtapiInterrupt: Resetting due to DRQ still up - %x
AtapiInterrupt: No SRB!
AtapiInterrupt: Unexpected interrupt. InterruptReason %x. Status %x.

IdeReadWrite: Returning BUSY status
IdeReadWrite: Starting sector is %x, Number of bytes %x
IdeReadWrite: Cylinder %x Head %x Sector %x
IdeReadWrite 2: Returning BUSY status %x
IdeReadWrite: DRQ never asserted (%x) original status (%x)

IdeVerify: Starting sector is %x, Number of bytes %x
IdeVerify: Cylinder %x Head %x Sector %x

AtapiSendCommand: Command %x to device %d
AtapiSendCommand: Entered with status %x
AtapiSendCommand: DSC not set. %x
AtapiSendCommand: Entered with status (%x). Attempting to recover.
AtapiSendCommand: DRQ still asserted.Status (%x)
AtapiSendCommand: Issued soft reset to Atapi device. 
AtapiSendCommand: Wait for int. to send packet. Status (%x)
AtapiSendCommand: DRQ never asserted (%x)

IdeSendCommand: Command %x to device %d
IDE disk %x - #sectors %x, #heads %x, #cylinders %x
IdeSendCommand: Unsupported command %x

AtapiStartIo: Already have a request!
AtapiStartIo: SRB to abort already completed
AtapiStartIo: Reset bus request received
AtapiStartIo: Reset bus failed
AtapiStartIo: Srb %x complete with status %x

UM8886b Does Not Exist
UM8886b IDE Is Not Enabled

ATAPI IDE MiniPort Driver
ScsiDebugPrint
ScsiPortReadPortUshort
ScsiPortReadPortUchar
ScsiPortMoveMemory
ScsiPortReadPortBufferUshort
ScsiPortStallExecution
ScsiPortWritePortUchar
ScsiPortWritePortUshort
ScsiPortWritePortUlong
ScsiPortNotification
ScsiPortCompleteRequest
ScsiPortGetDeviceBase
ScsiPortConvertUlongToPhysicalAddress
ScsiPortFreeDeviceBase
ScsiPortGetBusData
ScsiPortReadPortBufferUlong
ScsiPortWritePortBufferUshort
ScsiPortLogError
ScsiPortInitialize
ScsiPortReadPortUlongSCSIPORT.SYS


VS_VERSION_INFO
StringFileInfox
040904B0
CompanyName United Microelectronics Corp
FileDescription ATAPI IDE Miniport Driver for UM8886B
FileVersion 1.06
InternalName umc86b.mpd
LegalCopyright Copyright © United Microelectronics Corp.1994-1995
OriginalFilename atapi.sys
ProductName UM8886B8
ProductVersion 673A.1060D
VarFileInfo
Translation

umc86B.mpd

NB10  C:\DDK\Block\SAMPLES\MINIPORT\88

86b\umc86B.pdb